The hook-arm garbage truck is mainly used for municipal sanitation garbage collection and urban garbage transportation, especially for the collection and transportation of residential garbage. We can also call it a detachable garbage truck. There are several garbage bins on the car. This realizes that it can work with rubbish bins in multiple locations. The back cover of the garbage bucket is a movable door that can be opened upward. To prevent the garbage in the garbage box from overflowing during the garbage transportation process, four locking devices are used to lock it. The garbage can be dumped by opening the locking device. Self-unloading fully hydraulic operation, easy to use and easy to operate. This garbage truck is more suitable for schools, communities, shopping malls and other places. What do we need to pay attention to when using the hook-arm garbage truck? The first thing to say is that the car can't exceed the maximum shipping weight set by the factory. Simply put, it can't be overloaded. Otherwise, it will cause too much pressure when the hook arm is packed. Damage to the hydraulic components may result in oil leakage. The clutch pulley slips. In severe cases, the clutch may burn. Before carrying out the loading operation, the hook-arm garbage truck shall ensure that the longitudinal beams of the box are located between the rollers of the sub-beams, ensuring that the longitudinal centerline of the vehicle coincides with the longitudinal central axis of the box body, and the above conditions must not be completed to re-adjust the vehicle. position. During the packing work, the throttle can be appropriately increased according to the weight of the garbage collected in the vehicle so that the garbage can be smoothly picked up. At the end of the operation, the electromagnetic clutch must be turned off in a timely manner to ensure that the electromagnetic clutch is in the clutched state, especially when the vehicle is in the off state. Otherwise, the hook arm type garbage truck battery may consume electricity quickly and cause the car to fail to start. In normal use, do not adjust the pressure of the pressure regulating valve. The manufacturer of the garbage truck has adjusted it after leaving the factory. The advantage of the hook-arm garbage truck over the swing-arm garbage truck is that the used bin may be much larger than that of the swing-arm garbage truck, and a larger-capacity transport vehicle can be used for the low-density domestic garbage. . If there are special requirements for the hook-arm garbage truck, the garbage truck manufacturer can also make appropriate modifications. The above is a brief introduction to the hook-arm garbage truck. (Wen/Jun Xun)
Continuous Waste Tyre Pyrolysis Plant
Pyrolysis Plant is used for recycling waste tire, waste plastic, waste rubber to fuel oil. According to the actual situation in every country and district, we developed different models of Batch Pyrolysis Plants for waste tires, rubber and plastic with daily capacity 25-40 tons.
Flowchat of Continuous Waste Tyre Pyrolysis Plant
Advantages of Continuous Waste Tyre Pyrolysis Plant
1. Large daily capacity of 25 MT raw materials, and can work 24 hours without any stop for 15-20 days;
2. Auto-loading, auto-discharging and oil coming out at the same time;
3. Only need fuel for the beginning 2-3 hours, then the sync gas generates itself is enough to support heating, saving fuel cost;
4. Low requirement on the raw materials, no need tiny granule, 5cm pieces acceptable for smooth running;
5. High efficiency condensers, more oil output, good quality oil, easy to clean.
6. Sync gas recycling system, fully burned after recycling and utilization, preventing pollution and saving fuel cost.
7. National patent smoke scrubber, can efficient remove the acid gas and dust of the smoke, environmental friendly to meet related national standards.
8. Easy to operate, need less manpower.
Technical Parameter of Continuous Waste Tyre Pyrolysis Plant
NO.
ITEM
Technical Parameter
1
Suitable Raw Materials
Small pieces of Waste tyre,rubber, waste plastic≤5cm
2
Operating Mode
Fully Continuous Operation
3
Structure
Horizontal Type Revolve
4
Loading and discharging
Fully Automatic Feeding and Discharging under High Temperature at Same Time
5
Capacity(24h)
8-20Mt
6
Work Pressure
Slightly Negative Pressure
7
Oil Yield of tyres
40%-45%
8
Reactor Rotational Speed
1R/M
9
Installation Power
110kw
10
Cooling Method
Cycle water
11
Type of Drive
Sprocket Wheel
12
Heating Method
Hot Air
13
Noise dB(A)
≤85
14
Main Reactor Weight (MT)
About 20Mt
15
Total Weight(MT)
About 45Mt
16
Installation Space Required
60m*20m
17
Manpower
2/shift
18
Shipment
5*40HC
19
Delivery time
≤70Days
Continuous Waste Tyre Pyrolysis Plant Continuous Pyrolysis ,Continuous Pyrolysis Plant,Continuous Waste Tyre Recycling,Waste Tyre To Oil Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclings.nl